Amplifier Configuration
In the case of electric guitars, an amplifier stack consisting of a head atop one cabinet is commonly called a half stack, while a head atop two cabinets is referred to as a full stack. The cabinet which the head sits on often has an angled top in front, while the lower cabinet of a full stack has a straight front. The first version of the Marshall stack was an amp head on an 8x12 cabinet, meaning a single speaker cabinet containing eight 12" guitar speakers. After six of these cabinets were made, the cabinet arrangement was changed to an amp head on two 4x12 cabinets, meaning four 12" speakers, to enable transporting the amp rig.
In heavy metal bands, the term "double stack" or "full stack" is sometimes used to refer to two stacks, with the main amplifier section of a second amplifier serving as a slave to the first and four speaker cabinets in total. Another name for the "Head & Cab" that comes from the 1960s and 1970s is "Piggyback". Vox amp stacks could be put on a tiltable frame with casters. Fender heads could be attached to the cab and had "Tilt-Back" legs, like those used on larger Fender combo amps. Typically, a guitar amp's preamplifier section (known as a 'pre') provides sufficient gain so that an instrument can be connected directly to its input, and its main amplification section (known as the 'power stage') sufficient power to connect loudspeakers directly to its output, both without requiring extra amplification.
Some touring bands have used the appearance of a large array of guitar amplifiers for aesthetic reasons. Some of these arrangements include one or more actual guitar cabinets, while others do not. In reference to a photograph (left) taken during an Immortal gig, showing that what appeared to the audience to be a wide formation of equipment was actually only the fronts of amplifiers mounted on a large frame, Gizmodo writer Rosa Golijan investigated the phenomenon and found that it was "not too uncommon".
Another arrangement, often used for public address amplifier systems, is to provide two stages of amplification in separate units. First a preamplifier or mixer is used to boost the instrument output, normally to line level, and perhaps to mix signals from several instruments. The output from this preamplifier is then connected to the input of a power amplifier, which powers the loudspeakers.
Performing musicians that use the "two-stage" approach (as opposed to an amplifier with an integrated preamplifier and power amplifier) often want to custom-design a combination of equipment that best suits their musical or technical needs, and gives them more tonal and technical options. Some musicians require preamps that include specific features. Acoustic performers sometimes require preamps with "notch" filters (to prevent feedback), reverb, an XLR DI output, or parametric equalization. Hard rock, metal, or punk performers may desire a preamplifier with a range of distortion effects. As well, some musicians have specific power amplifier requirements, such as low-noise design, very high wattage, the inclusion of limiter features to prevent distortion and speaker damage, or biamp-capable operation.
With the "two-stage" approach, the preamplifier and power amplifier are often mounted together in a rack case. This case may be either free-standing or placed on top of a loudspeaker cabinet. If many rack-mounted effects are used, the rack may be a large unit on wheels. Some touring players need several racks of effects units to reproduce on stage the sounds they have produced in the studio. At the other extreme, if a small rack case containing both preamp and power amp is placed on top of a guitar speaker cabinet, the distinction between a rack and a traditional amp head begins to blur. Another variation is to combine the power amplifier into the speaker cabinet, an arrangement called a powered speaker, and use these with a separate preamp, sometimes combined into an effects pedal board or floor preamp/processor.
Preamplifiers are also used to connect very low-output or high-impedance instruments to instrument amplifiers. When piezoelectric transducers are used on upright bass or other acoustic instruments, the signal coming directly from the transducer is often too weak and it does not have the correct impedance for direct connection to an instrument amplifier. Small, battery-powered preamps are often used with acoustic instruments to resolve these problems.
Read more about this topic: Guitar Amplifier